R3 2560 R3 ATmega2560-16AU USB-UART CH340C 86 I/O 5V/3.3V Development Board

Based on 0 reviews. - Write a review

$22.56

Ex Tax: $22.56

Stock: In Stock
Model: EB0041788
SKU: EB0041788

Qty

Add to Cart

Buy Now Ask Question

Add to Wish List Compare this Product

Feature:

The MegaXPRO R3 - Mega 2560 R3 is an extra I/O board, which is convenient to use for creating powerful projects with more functions.

With 86 I/O - 69 digital I/O pins, 17 analog inputs (YES, more pins unlike standard Arduino Mega 2560 with 70 I/O), 4 UARTs (hardware serial ports), one I2C and one SPI interface, and a larger memory space 256KB for your sketch1.

In addition, you can create a project with 3.3V or 5V logiclevel. Onboard has a solution for switch between 3.3V or 5V.

Just connect to your PC to USB and download the sketch1 from Arduino IDE.

MegaXPRO R3 - Mega 2560 R3 is open-source hardware, base on MCU ATmega2560! You can create your own projects or gadgets using the following files: schematic diagram, dimension diagram, pinout diagram, Eagle and Altium CAD library, datasheet, 3Dstep file, software library.

Programming:

The MegaXPRO R3 - Mega 2560 R3 controller can be programming with the Arduino(R) IDE software.

The MegaXPRO R3 - Mega 2560 R3 comes pre-installed with a bootloader for Arduino IDE, that allows you to upload new code to it without the use of an external hardware programmer. You can also direct program the microcontroller through the ICSP (In-Circuit Serial Programming).

Power:

The MegaXPRO R3 - Mega 2560 R3 can be powered via the USB connection or with an external power supply.

Note: The board has a resettable fuse that protects your computer's USB ports from shorts and overcurrent.

If more than 500 mA is applied to the USB port, the fuse will automatically break the connection until the short or overload is removed.

External power can come either from a DC adapter or battery to DC IN Jack or to VIN. The board can operate on an external supply:

TO VIN: of 7 to 12 volts.

TO 5V: 5V. (Logiclevel will be 5V, switch to 5V)

TO 3.3V: 3.3V. (Logiclevel will be 3.3V, switch to 3.3V)

TO VCC-IOREF: 5V (Logiclevel will be 3.3V) or 3.3V (Logiclevel will be 3.3V). In this case, power stabilizers will be disconnected and the board will use small power. The switch needs to be unsoldered connection. Details in the datasheet.

If to VIN supplied with less than 6.4V, however, the 5V pin may supply less than five volts and the board may become unstable. If using more than 12V to VIN, the voltage regulator may overheat and damage the board. The recommended range is 7~12 volts.

Memory:

The ATmega2560 has 256 KB of flash memory for storing code (of which 8 KB is used for the bootloader), 8 KB of SRAM and 4 KB of EEPROM (which can be read and written with the EEPROM library).

Input and Output:

See the pinout diagram document.

MegaXPRO R3 - Mega 2560 R3 ports:

Each of the 70 digital pins on the MegaXPRO R3 - Mega 2560 R3 can be used as an input or output, using pinMode(), digitalWrite(), and digitalRead() functions. They operate at a voltage selected of the switch: Logiclevel. Each pin can provide or receive 20 mA as recommended operating condition and has an internal pull-up resistor (disconnected by default) of 20-50 k ohm. A maximum of 40mA is the value that must not be exceeded to avoid permanent damage to the microcontroller. In addition, some pins have specialized functions:

Serial: D0 (RX0) and D1 (TX0); Serial 1: D19 (RX1) and D18 (TX1); Serial 2: D17 (RX2) and D16 (TX2); Serial 3: D15 (RX3) and D14 (TX3). Used to receive (RX) and transmit (TX) TTL serial data. Pins D0 and D1 are also connected to the corresponding pins of the USB-UART Serial chip (ATmega16U2/ CP2104/ CH340C from a model of board).

External Interrupts: D2 (interrupt 0), D3 (interrupt 1), D18 (interrupt 5), D19 (interrupt 4), D20 (interrupt 3), and D21 (interrupt 2). These pins can be configured to trigger an interrupt on a low level, a rising or falling edge, or a change in level. See the attachInterrupt() function for details.

PWM: D2 to D13 and D44 to D46. Provide 8-bit PWM output with the analogWrite() function.

SPI: D50 (MISO), D51 (M0SI), D52 (SCK), D53 (SS). These pins support SPI communication using theSPI library. The SPI pins are also broken out on the ICSP header.

I2C (TWI): D20 (SDA) and D21 (SCL). Support TWI communication using the Wire library.

Analog IN: The MegaXPRO R3 - Mega 2560 R3 has 17 analog inputs, each of which provides 10 bits of resolution (i.e. 1024 different values). By default, they measure from ground to power level (5/3.3 volts), though is it possible to change the upper end of their range using the AREF pin and analogReference() function.

There are a couple of other pins on the board:

AREF: The reference voltage for the analog inputs. Used with analogReference().

Reset: Bring this line LOW to reset the microcontroller. Typically used to add a reset button to shields which block the one on the board.

Communication:

The MCU-PRO Mega 2560 controller has a number of facilities for communicating with a PC, other digital boards, or other microcontrollers. The MCU ATmega2560 provides four hardware UARTs for TTL serial communication. A USB-UART on the board channels one of these over USB and provides a virtual com port to software on the PC (OS will recognize the board as a COM port automatically). The Arduino IDE Software includes a serial monitor which allows simple textual data to be sent to and from the board. The RX and TX LEDs on the board will flash when data is being transmitted via the USB-UART chip and USB connection to the PC (but not for serial communication on pins D0 and D1). The MegaXPRO R3 - Mega 2560 R3 also supports I2C(TWI) and SPI communication. The Arduino IDE Software includes a Wire library to simplify the use of the I2C(TWI) bus. For SPI communication, use the SPI library.

USB:

The MegaXPRO R3 - Mega 2560 R3 have micro USB for connecting to PC, also on board have 4 pinouts for connecting the external USB cable or USB socket.

LED RGB:

The MegaXPRO R3 - Mega 2560 R3 have RGB LED connected to D11, D12, D13.

Microcontroller	ATmega2560
USB-TTL converter	CP2104
Power Out	5V-800mA, 3.3V-800mA
Power IN USB.	USB 5V
Power IN. VIN	VIN 7~9V
Power Consumption	120mA
LogicLevel	5V/3.3V
USB	Micro USB / USB-B
Clock Frequency	16MHz
Operating Supply Voltage	5V/3.3V
Digital I/O	69
Analog I/O	17
Memory Size	256kb
Data RAM Type/Size	8Kb
Data ROM Type/Size	4Kb
Interface Type	ISP, I2C, UART, USB
Operating temperature	−40С°/+85С°
Form-factor	Arduino Mega R3

Documents:

Dimensional drawing: Click here to open

Input and Output (I/O) diagram: Click here to open

Schematic: Click here to open

Arduino IDE - Library & Instruction: Click here to open

Tutorial: Click here to open

Package includes:

1 x Development Board

Shipping Time

After you successfully placed an order at RenhotecIC.com, you will receive a confirmation email with your invoice. Once your order is shipped, you will be emailed with the tracking information of your package. Also, you can choose your preferred shipping method during the checkout process. Kindly advise: please select DHL/FedEx if you need our product urgently.

The timeline of the whole shipping process is shown below:

The total delivery time is calculated from the time your order is successfully placed to the time received. Total delivery time is broken down into processing time and shipping time.

Processing time: The time it takes to prepare your item(s), includes preparing your items, performing quality inspections, and packaging for shipment. Normally, the processing time is 1-3 days (Only include Monday to Saturday ) after getting your order.

Shipping time: The time for your item(s) to travel from our warehouse to your destination. The shipping time depends on the shipping method you chose. Please refer to the shipping rate section for details.

Shipping Rates

You could choose the shipping method based on your preference during checkout, different shipping methods will apply different rates and shipping times. Please check the following chart for detail:

Shipping Method Shipping Rates Shipping Times
Flat Shipping (Promotion)
$10 About 5-30 Working Days to Worldwide (Only include Monday to Saturday )
Standard Express（0.5KG starting price listed）
Based On Weights About 5-15 Working Days to Worldwide (Only include Monday to Saturday )
Priority Express （0.5KG starting price listed）
Based On Weights About 3-7 Working Days to Worldwide (Only include Monday to Saturday )

In addition, the transit time depends on where you're located, the shipping method you choose, and where your package comes from. We will keep you informed of any problems here to help you get your order as soon as possible.

If you want to know more information, please contact the customer service by contact form or sales@renhotecic.com. We will settle your problem as soon as possible. Enjoy shopping!

Tags: Development Board