PWM Stepper Motor Driver Simple Controller Speed Controller Forward and Reverse Control Pulse Generation

Based on 0 reviews. - Write a review

$11.99

Ex Tax: $11.99

Stock: In Stock
Model: EB0051607
SKU: EB0051607

Qty

Add to Cart

Buy Now Ask Question

Add to Wish List Compare this Product

Content-Length: 3974 >

Feature:

Product name: simple controller

Model: CW-S01

It can generate PWM signal. There is a jumper on the board, which can be set and selected. By default, it is set to generate pulse frequency signal.

Product Manual:

1. When the controller generates a pulse frequency signal, it can supply a stepper driver as a signal. To control the stepper motor, it must be equipped with a driver.

(This simple controller + stepper driver + stepper motor + DC power supply can form a simple control platform.)

2. The controller can generate a pulse frequency signal or a PWM pulse width signal. There is a jumper on the board, which can be set and selected. By default, they are set to generate pulse frequency signals.

REQ is to generate pulse frequency signal

PWM is to generate PWM signal

3. When the controller generates a pulse frequency signal, there are three types of high, medium and low frequency signals that can be selected with a jumper. The frequency parameters are approximately:

High: 5.8KHZ-127KHZ

Middle: 590HZ-15.8KHZ

Low: 82HZ-2.3KHZ,

Frequency measurement: You can measure PUL and common cathode (GND) two ports.

4. The power supply has 2 sets of power input, and 2 sets only need to connect one set of power supply. It is recommended to use a power supply of more than 15V. Connect to the power supply of the 2-bit terminal, do not connect the positive and negative.

One group is the power supply connected to DC 15-160VDC, and the recommended operating voltage is 15-80VDC.

The other group is 5-12VDC. When used with the driver, it is recommended to use a minimum of 12V, not a 5V power supply, not at 5V, the power supply is connected to "5-12V input", and the power supply is connected to the "common cathode".

5. Length * width * height: about 73 * 51 * 37MM

Controller

Driver

PUL

Pulse negative terminal (PUL-)

DIR

Negative direction (DIR-)

ENA

Enable negative terminal (EN-)

Common anode

Common port (COM or + 5V or PUL + DIR + EN + are connected at the same time)

Common cathode

Common ground (GND)

5-12V input+

The positive end of the 12V power supply is generally empty.It is recommended to use a power supply of more than 15V.

Example: Wiring with the common anode of the driver. If it is driven by 6 signal lines, the + 5V common terminals of the three signals must be connected in parallel to form a line and all connected to the common anode terminal.

PWM-Stepper-Motor-Driver-Simple-Controller-Speed-Controller-Forward-and-Reverse-Control-Pulse-Genera-1666759

Package includes:

1 x Controller

Note:

1. If you want to use the start or stop function, the ENA enable terminal on the controller must be connected to the driver with a common cathode or a common anode.

2. The forward and reverse rotation and the start and stop of the motor can be controlled by pressing the button.

3. The speed of the motor can be controlled by adjusting the potentiometer to change the frequency.

4. The switch of the motor's forward / reverse rotation and start / stop is an ordinary switch with self-locking.

5. If you want to connect the switches that control forward and reverse, and open or stop, to the chassis panel, you can refer to the following instructions.

Change the forward and reverse, the start-stop button into a lead-wire switch, see the pin position on the back:

1. When the common cathode is connected, the 1 and 3 pins are processed, and the 2, 4, 5, and 6 pins are empty

2. When the common anode is connected, the 1 and 2 pins are processed, and the 3, 4, 5, and 6 pins are empty

The two switches are the same pin lead.

Shipping Time

After you successfully placed an order at RenhotecIC.com, you will receive a confirmation email with your invoice. Once your order is shipped, you will be emailed with the tracking information of your package. Also, you can choose your preferred shipping method during the checkout process. Kindly advise: please select DHL/FedEx if you need our product urgently.

The timeline of the whole shipping process is shown below:

The total delivery time is calculated from the time your order is successfully placed to the time received. Total delivery time is broken down into processing time and shipping time.

Processing time: The time it takes to prepare your item(s), includes preparing your items, performing quality inspections, and packaging for shipment. Normally, the processing time is 1-3 days (Only include Monday to Saturday ) after getting your order.

Shipping time: The time for your item(s) to travel from our warehouse to your destination. The shipping time depends on the shipping method you chose. Please refer to the shipping rate section for details.

Shipping Rates

You could choose the shipping method based on your preference during checkout, different shipping methods will apply different rates and shipping times. Please check the following chart for detail:

Shipping Method Shipping Rates Shipping Times
Flat Shipping (Promotion)
$10 About 5-30 Working Days to Worldwide (Only include Monday to Saturday )
Standard Express（0.5KG starting price listed）
Based On Weights About 5-15 Working Days to Worldwide (Only include Monday to Saturday )
Priority Express （0.5KG starting price listed）
Based On Weights About 3-7 Working Days to Worldwide (Only include Monday to Saturday )

In addition, the transit time depends on where you're located, the shipping method you choose, and where your package comes from. We will keep you informed of any problems here to help you get your order as soon as possible.

If you want to know more information, please contact the customer service by contact form or sales@renhotecic.com. We will settle your problem as soon as possible. Enjoy shopping!