Intelligent Microwave Sensor Switch AC220V-240V Human Body Induction Sensor Corridor Photoelectric Sensor

Based on 0 reviews. - Write a review

$10.70

Ex Tax: $10.70

Stock: In Stock
Model: EB0047508
SKU: EB0047508

Qty

Add to Cart

Buy Now Ask Question

Add to Wish List Compare this Product

Introduction: >>>More informations: Click here to open<<<

The microwave sensor is an active sensor. The HF sensor emits high-frequency electromagnetic waves (5.8 GHz) and receives their echoes (power consumption less than 2 MW). This sensor detects changes in the echoes and even small movements within its detection ran ge. . The microprocessor then triggers the "lights up" c0mmand. Signals through the door, glass plates and thin walls are likely to be detected.

Installation reminder:

The sensor switch has a blind spot in the center. If it is installed in a small indoor environment (such as a bathroom or kitchen), try to install the position to the side or install it in the corner, because the sensing area will be better, otherwise the vertical center activity may not be sensed.

1. Control principle:

The microwave sensor uses the Doppler principle to transmit and receive high-frequency microwave signals (accurately sense the movement changes of the object), and to control the opening (lighting) and off (extinguishing) of the load lamps through signal amplification and intelligent recognition of the single-chip program.

* Doppler principle, the principle of ra dar, is widely used in aviation, aerospace, and military.

2. Intelligent induction:

1) When a person enters the sensing detection range (within 16m diameter), the load lamp lights up; when the person passes the inductive detection range and the set delay time counts down, the load lamp automatically goes out.

2) When the person enters the inductive detection range and the load lamp has been illuminated, if the person stays within the inductive detection range, as long as the person has a slight movement (including the movement of the limb) before the end of the set delay time countdown, The sensor will drive the load luminaire to illuminate continuously until the person leaves and the set time countdown is over, the load luminaire is automatically extinguished.

3. Intelligent identification:

1) Simply put, this product can be set to not light up during the day, only when someone lights at night; it can also be set to light at any time according to demand.

2) This product has a variety of light setting options, customers can adjust according to their needs, to meet the lighting requirements in different environments.

4. Anti-interference:

As we all know, there are many signals with different frequencies in the space (such as 3GHz signal of phone, 2.4GHz signal of wifi, 433KHz signal of TV remote control, sound wave signal, etc.), and some signals are similar to human body induction signals. Our products can intelligently identify useful human body sensing signals, prevent false triggering of other interference signals, and ensure product reliability.

Note:

Regarding the problem of connecting LED lights, etc., since the LED has a driving power supply, when the power is turned on, the instantaneous current is very large. This sensor switch generally has no problem with the LED below 150W, and even if the quality of the LED driving board is good, there are no problems with 600W, but The market generally has a lot of LEDs. Such as ordinary incandescent lamps and other loads, can be up to 1200W, which is not connected.

Parameters:

Size: 75*41*42mm

Working voltage: AC220-240V 50/60Hz

Load power: 1200 watts (resistive load, incandescent lamp and other resistive appliances) /600W (inductive load, energy-saving lamps and other non-resistive appliances)

Interface: 3-pin pluggable port (N, L, L'), 1.5mm 2 cable

Detection principle: microwave moving detect

Installation method: indoor, wall or ceiling installation

HF system: 5.8GHz +/- 75 MHz CW radio, ISM band

Transmit power: <2mW

Detection angle: 360°, 160°

Detection: 0.3 .., 3 m/s (1 ... 10 km/h)

Distance: 2-10m (radius), adjustable

Working delay: 10 seconds to 30 minutes, adjustable

Light control illuminance: 10 ~ 500 LUX, adjustable

Power consumption: close to 0.5W

Working temperature: -10 to +70 °C

Protection level: IP20

Product weight: 80g

Package includes:

1 x Sensor switch

Intelligent-Microwave-Sensor-Switch-AC220V-240V-Human-Body-Induction-Sensor-Corridor-Photoelectric-S-1529308

Shipping Time

After you successfully placed an order at RenhotecIC.com, you will receive a confirmation email with your invoice. Once your order is shipped, you will be emailed with the tracking information of your package. Also, you can choose your preferred shipping method during the checkout process. Kindly advise: please select DHL/FedEx if you need our product urgently.

The timeline of the whole shipping process is shown below:

The total delivery time is calculated from the time your order is successfully placed to the time received. Total delivery time is broken down into processing time and shipping time.

Processing time: The time it takes to prepare your item(s), includes preparing your items, performing quality inspections, and packaging for shipment. Normally, the processing time is 1-3 days (Only include Monday to Saturday ) after getting your order.

Shipping time: The time for your item(s) to travel from our warehouse to your destination. The shipping time depends on the shipping method you chose. Please refer to the shipping rate section for details.

Shipping Rates

You could choose the shipping method based on your preference during checkout, different shipping methods will apply different rates and shipping times. Please check the following chart for detail:

Shipping Method Shipping Rates Shipping Times
Flat Shipping (Promotion)
$10 About 5-30 Working Days to Worldwide (Only include Monday to Saturday )
Standard Express（0.5KG starting price listed）
Based On Weights About 5-15 Working Days to Worldwide (Only include Monday to Saturday )
Priority Express （0.5KG starting price listed）
Based On Weights About 3-7 Working Days to Worldwide (Only include Monday to Saturday )

In addition, the transit time depends on where you're located, the shipping method you choose, and where your package comes from. We will keep you informed of any problems here to help you get your order as soon as possible.

If you want to know more information, please contact the customer service by contact form or sales@renhotecic.com. We will settle your problem as soon as possible. Enjoy shopping!

Tags: Sensor Switch