ESP32 Thermal Camera Development Kit Lepton 3.0 Imaging Camera 6-Axis IMU MPU6886 Digital Infrared Thermal Image Sensor Module

 Note:
M5StickT is designed fully based on M5StickC, and the casing is 3D printed. Aiming for DIY use only. We didnt apply any certificates for this model. Pls consider whether it's OK to use in Japan. Thx! 
 
Description:
 

M5StickT is an exquisite and compact infrared thermal imaging camera. It adopts the latest FLIR Lepton 3.0 long-wave infrared (LWIR) camera core with an effective resolution of 160 * 120 for a clear and stable image. As it is a large area non-contact infrared sensor, it is a good solution for temperature measurement. Its main control chip is Espressif’s ESP32, which has built-in support for Wi-Fi and Bluetooth connections, and computing speeds of up to 240Mhz. This provides a favorable guarantee for image output with a FPS reaching 7 and above. The screen is 1.14 inches and has a resolution of 135 * 240. The device comes with a rich variety of hardware resources: An on-board 6-axis Inertial Measurement Unit, a digital microphone and a power management chip and a built-in 300mAh battery, all embedded into the device. In terms of interactive operation, two programmable buttons and a rotary encoder are provided. In order to facilitate users to connect more peripherals, a 4 Pin PH2.0 interface with I2C support is provided at the bottom. The body is 3D printed from high quality Black Nylon filament. In addition, an M3 screw hole and a 1/4" screw hole are provided underside for easy mounting.

Lepton 3.0 Parameter

Effective Pixels	160*120
Field of view	56°
Fast imaging time	< 500ms
Effective Frame Rate	8.7Hz
Input Clock	25MHz
Pixel Size	12μm
Low operating power	150 mW (operating), 650 mW (during shutter event), 5 mW (standby)
Scene Dynamic Range	Low Gain Mode: -10 to 400°C; High Gain Mode: -10 to 140°C
Spectral Range	8 to 14µm
Thermal Sensitivity	<50 mK(0.050°C)
Optimum Temperature Range	-10°C to +80°C

Notice:

M5StickT only supports WIN10 & Linux & MAC(<10.15) free drive, the rest of the operating system requires users to install the driver.

Installation steps: 1. Click the link below to download the driver installation package. 2. Connect the device and open the Computer Device Manager port option. 3. Right click on the unrecognized device and perform a manual update.

Driver download Link

Feature:

• 5V DC power supply
• USB Type-C
• ESP32-based
• Case Material: Nylon 3D print
• FLIR Lepton 3.0
• 4 MByte Flash
• 6-Axis IMU: MPU6886
• Microphone:SPM1423
• 2 Buttons, 1 Reset
• IPS LCD(1.14 inch)
• 2.4G Antenna: Proant 440
• 300 mAh Lipo Battery
• PMU: AXP192
• Dial encoder
• 4P PH2.0 Interface
• Wight: 26g
• Size: 48 * 30 * 29mm

ESP32 Features:

• 240 MHz dual core Tensilica LX6 microcontroller with 600 DMIPS
• Integrated 520 KB SRAM
• Integrated 802.11b/g/n HT40 Wi-Fi transceiver, baseband, stack and LWIP
• Integrated dual mode Bluetooth (classic and BLE)
• Hall sensor
• 32 kHz crystal oscillator
• PWM/timer input/output available on every GPIO pin
• SDIO master/salve 50MHz

Package Included:

• 1x M5StickT
• 1x USB Type-C(20cm)

Application:

• Car engine failure check
• Building dehumidification insulation sealing test
• Industrial furnace inner wall refractory crack
• Outdoor observation of animals at night

Usage:

Press the reset button to power on. The default display screen is RGB display mode. The left side is the temperature image, the upper right is the power display, and the lower right is the histogram and temperature range. The temperature range is automatically adjusted with the target temperature. The default bulls-eye automatically tracks the maximum temperature. Press the right button-A to switch the tracking mode (minimum / center / maximum value), press the button-B to switch the image display mode (GRAY / GOLDEN / RAINBOW / IRONBLACK / RGB). Dial encoder controls the display sensitivity (adjust the display temperature and color gamut), and long press the reset button for 6 seconds to turn off.