DC 12V-36V 15A 500W Brushless Motor Controller BLDC Driver Board With Stall Over-current Protection Supports Hallless Motors

Based on 0 reviews. - Write a review

$12.99

Ex Tax: $12.99

Stock: In Stock
Model: EB0048600
SKU: EB0048600

Qty

Add to Cart

Buy Now Ask Question

Add to Wish List Compare this Product

Specification:

Operating voltage: DC 12V-36V

Operating Current: <=15A

Driver Power: <=500W

Speed Voltage: 0.1V-5V

Operating Temperature: -40~85°C

Humidity: 90%RH

Stall protection: Yes

Enable Control: Yes

Over-current protection: Yes

Steering control: Yes

Speed control signal: Yes

Size: 63 x 42 x 17mm (L x W x H); Probe size 3mm, length: fixing hole center distance 57mm; width: fixed hole center distance 36.5mm

Power terminal Out:

VCC(positive power supply)

GND(negative one)

MC(motor phases W)

MB(motor phases V)

MA(motor phase U)

Set for the control side:

GND: control terminal ground

VR: the governor end 0-5V(corresponding to 10% of motor speed -100%)

ZF: reversing control(connected to 5V or ground can charge the motor rotation direction)

M: tachometer pulse output(depending on the number of motor poles corresponding to the number of pulse per revolution of the output number)

EL: enable control terminal(connected to 5V ot ground running then 5V, grounding the motor stops)

5V: 5V control terminal

Wiring:

Control terminal for SET:

1. The motor speed control wiring methods: available potentiometer system speed can also be connected to the MCU control, when the potentiometer control wiring, the potentiometer middle pin is connected to VR speed port, potentiometer connected to both ends of 5V and GND terminal voltage more high speed faster.

2. Motor steering control wiring methods: you can switch control can also be connected to the MCU control, to GND in one direction, then in one direction 5V.

3. Pulse speed signal: high and low output . IC can not understand the information with the customer request.

Note:

Motor driver board 12-36V DC power input, VCC positive power supply,GND power supply is negative.

Electrical wiring methods: Brushless DC motor for the three lines, corresponding MA/U, MB/V, MC/W

Tips:

If you use less than 60W, without additional heat sink , be sure to add more than 60W

heatsink fins drive efficiency without lowering the temperature is too high will shine into permanent damage! The size of the heat sink may be a bad environment based work(recommended cooling surface area greater than 200 square centimeters)!When installing the heat sink ,must pay attention to the back of the module 6 MOS pipe insulation, no insulation, it will be adhered to drive plate permanently damaged! Proposes to add insulation films, both sides of the insulating sheet plus thermal grease!

Package Includes:

1 x 12-36V 500W Brushless Motor Controler(If you need Hall singal, please add a comment while finishing your order.)

DC-12V-36V-15A-500W-Brushless-Motor-Controller-BLDC-Driver-Board-With-Stall-Over-current-Protection--1311915

Shipping Time

After you successfully placed an order at RenhotecIC.com, you will receive a confirmation email with your invoice. Once your order is shipped, you will be emailed with the tracking information of your package. Also, you can choose your preferred shipping method during the checkout process. Kindly advise: please select DHL/FedEx if you need our product urgently.

The timeline of the whole shipping process is shown below:

The total delivery time is calculated from the time your order is successfully placed to the time received. Total delivery time is broken down into processing time and shipping time.

Processing time: The time it takes to prepare your item(s), includes preparing your items, performing quality inspections, and packaging for shipment. Normally, the processing time is 1-3 days (Only include Monday to Saturday ) after getting your order.

Shipping time: The time for your item(s) to travel from our warehouse to your destination. The shipping time depends on the shipping method you chose. Please refer to the shipping rate section for details.

Shipping Rates

You could choose the shipping method based on your preference during checkout, different shipping methods will apply different rates and shipping times. Please check the following chart for detail:

Shipping Method Shipping Rates Shipping Times
Flat Shipping (Promotion)
$10 About 5-30 Working Days to Worldwide (Only include Monday to Saturday )
Standard Express（0.5KG starting price listed）
Based On Weights About 5-15 Working Days to Worldwide (Only include Monday to Saturday )
Priority Express （0.5KG starting price listed）
Based On Weights About 3-7 Working Days to Worldwide (Only include Monday to Saturday )

In addition, the transit time depends on where you're located, the shipping method you choose, and where your package comes from. We will keep you informed of any problems here to help you get your order as soon as possible.

If you want to know more information, please contact the customer service by contact form or sales@renhotecic.com. We will settle your problem as soon as possible. Enjoy shopping!

Tags: Brushless Motor Controller